• New
GENPRO10X1 · NOCO 10A on-board | telebaterias.com
GENPRO10X1 · NOCO 10A on-board | telebaterias.com
GENPRO10X1 · NOCO 10A on-board | telebaterias.com
GENPRO10X1 · NOCO 10A on-board | telebaterias.com
GENPRO10X1 · NOCO 10A on-board | telebaterias.com

GENPRO10X1 by NOCO: 12V 10A on-board charger for batteries up to 230 Ah

NOCO

Is your 12 V battery a big one? The GENPRO10X1 delivers 10 A from a single bank and goes up to 230 Ah: a 100 Ah battery at half charge recovers in around 7 h.

10 A from one 12 V output | Batteries up to 230 Ah | 100 Ah from 50 % in about 7 h | Sealed IP68, fixed mounting

Free quote, no obligation

Request a quote for your GENPRO10X1 by NOCO: 12V 10A on-board charger for batteries up to 230 Ah

  • Reply in under 4 working hours
  • Best price guaranteed
Attach photo (optional)
Photo of the old battery or vehicle documentation · Max. 3 · 8 MB · images or PDF
Share

Frequently Asked Questions

insert_link

Buying a battery on telebaterias.com has the following advantages:

  1. First of all, the price. Buying a battery online is much cheaper than buying a battery in a physical store, mainly thanks to our high sales volume.
  2. On the other hand, at telebaterias.com we have commercial agreements with the main battery manufacturers. Thanks to our high turnover, our products are stored for a few days at the factory and reach our customers in the best possible condition. Our batteries therefore have the most recent date of manufacture.
  3. Finally, thanks to our professional technical advice, you can change your battery yourself at the best price
insert_link

To find out if a battery is suitable for my vehicle, the best thing to do is to contrast the characteristics of the battery we have installed with the one we are going to buy.

Battery technology.

First of all, we must check that the type of battery is compatible with the one we are going to buy. If the technology is special, it is usually indicated on the battery. Battery technology is especially relevant in vehicles equipped with a start-stop system.

Measurements.

It is very important that the battery enters the cabin prepared for installation. Keep in mind that the measurements of the batteries are the maximum measurements of the same with all its edges, with the height of the terminal, with the tab for fastening, etc ... Therefore, if you have the appropriate gap for the measurement battery, you will have no problem installing it. In many cases you will see that you have a larger gap to install a larger battery. In these cases, we recommend that you put the battery with the highest amperage that fits into the hole.

Arrangement of the terminals.

It is essential that the positive of the battery matches the location of the positive of the battery you have installed. The convention is to locate the positive being as close as possible to the terminals, since in some cases, the battery may have the terminals closest to the conductor and in other cases closer to the license plate.

However, if you look closely at the photo you can see if the positive of the battery matches the one you have.

In general, except for Asian, American or some off-road vehicles, it is normal for the positive to be on the right.

This is a general guide. However, if you have any questions, contact us and we will be happy to advise you on the most suitable battery for your vehicle.

GENPRO10X1 by NOCO: 12V 10A on-board charger for batteries up to 230 Ah

Is a 5 A charger too small for my 200 Ah house battery? Most likely, and that is where the GENPRO10X1 comes in: it doubles the current to 10 A on a single bank and is rated for 12 V batteries up to 230 Ah. According to the manufacturer, from 50 % discharge a 230 Ah battery takes about 17.3 h and a 100 Ah one about 7 h.

Which batteries does it take? 12 V lead-acid (wet, gel, MF, calcium, EFB, AGM) and 12 V lithium with a BMS, with 12V, AGM, lithium, repair and force modes. It is sealed to IP68 and installs permanently in any orientation.

Before you order, check

  • ›  The voltage: 12 V batteries only.
  • ›  The capacity: up to 230 Ah; if yours is 120 Ah or less, the GEN5X1 (5 A) will also do.
  • ›  If you have more than one battery: the GENPRO10X2, X3 and X4 offer 2, 3 and 4 banks of 10 A.
  • ›  The technology: lead-acid or 12 V lithium with BMS.
  • ›  Call us if you would like us to confirm the right model for your boat.

Features

  • ›  One 10 A bank for 12 V batteries up to 230 Ah.
  • ›  Approximate times from 50 % discharge: 40 Ah in 3 h, 100 Ah in 7 h, 230 Ah in 17.3 h.
  • ›  Lead-acid (wet, gel, MF, calcium, EFB, AGM) and 12 V lithium with BMS, LiFePO4 included.
  • ›  12V, AGM, lithium, repair and force modes; detects from 1 V.
  • ›  Temperature compensation and last-mode memory.
  • ›  Sealed IP68 housing; operates from -20 °C to +40 °C.
  • ›  150 W output; 145 × 122 × 71 mm and 1.81 kg.

In the box

  • ›  GENPRO10X1 on-board charger
  • ›  2 x #8 27 mm self-tapping screws
  • ›  User guide and warranty

Technical data

Mains input voltage100-240 VAC, 50-60 Hz
Output power150 W max.
Charging banks1
Charging current10 A (12 V)
Battery voltage12 V
Battery chemistriesLead-acid (wet, gel, MF, calcium, EFB, AGM) and 12V lithium with BMS (incl. LiFePO4)
Battery capacityUp to 230 Ah; maintains all battery sizes
Charging modes12V, 12V AGM, 12V Lithium, Repair and Force
Low-voltage detection1 V (Force Mode: 0 V)
Back current drain< 0.5 mA
Operating temperature-20 °C to +40 °C
Housing protectionIP68
CoolingNatural convection
DC cable lengthapprox. 1.83 m
Approx. charging time (50% depth of discharge)20 Ah: 1.5 h · 40 Ah: 3 h · 100 Ah: 7 h · 230 Ah: 17.3 h
Dimensions (L x W x H)145 x 122 x 71 mm
Weight1.81 kg

  • Brand
    NOCO
  • Reference
    TB-NOCO-GENPRO10X1
  • MPN
    GENPRO10X1

noco-genpro10x1-ficha-tecnica.pdf

Download (2.39MB)
Closed prices without surprises with VAT and shipping costs included! (Iberian Peninsula)
Delivery service in 24 hours! Receive your battery comfortably at home
Batteries with the latest date of manufacture

16 other products in the same category

Back to top